G-Series Programmable IO - Device Description (XML)

CODESYS version:

• Beijer G PIO XML(V2)_Update_2023.01.11.zip
• Beijer G PIO XML(V3)_Update_2023.01.11.zip
• Beijer G PIO XML(V3)_Update_2023.07.10.zip
• Beijer G PIO XML_Update_2024.03.06.zip

GT-5904 - Device Description XML (Beijer)

​Can be used in combination with G-series Programmable IO

• GT-5904 - Device Description XML (Beijer).zip

G series, BootP Server for IP-setting at GN-9372 and GN-9289

​Software using Bootstrap Protocol (RFC 951) is for IP Address setting to Beijer G-series products.

• Copy file to PC
• Run "BootpServer.exe"
  

Link: G series, IP address, Subnet and Gateway Setting (KI00389)

• BootpServerVer1000_Beijer.zip

PIO Firmware Update Tool, for G- and M-series devices

• PIO Firmware Update Tool(1.0.0.3).zip
• PIO Firmware Update Tool(1.0.0.5).zip
• Update firmware of Beijer Programmable IO (Rev.3).pdf

CODESYS V3.5 SP11 Patch 3, required for G- and M-series PIOs FW rev 2.xxx

​This is the officially tested CODESYS version by Beijer Electronics.
It's required for G-series and M-series PIO using CODESYS RT 3.5.11.30

• features-and-improvements-V35SP11-en.pdf
• ReleaseNote-CODESYS-V351130.pdf
• Setup_CODESYSV35SP11Patch3.exe
• Setup_CODESYSV35SP11Patch3_x64.exe

IO Guide Pro 1.2.0.3, for S- and G-series

​IOGuidePro is a configuration tool for the S- and G-series remote IO.
IOGuidePro can be used for assembling, parameter setting, addressing, commisioning and documentation of FnIO IO nodes.
Software has both on-line and off-line functionality and include all S- and G-series Network Adaptors.

• IOGuidePro_1_2_0_3.zip

IOGuide2(Beijer)_BETA_20250220 G- and M-series devices

​Important information!

• IOGuide2(Beijer)_BETA_20250220.zip

IO Guide Pro 1.4.0.0 beta2, for Beijer G-series

• IOGuidePro(Crevis)_1.4.0.0)_beta2.zip

Release Notes for PIO - Programmable IO

• Release Notes for PIO Beijer(V1-V2)_Rev2007.pdf
• Release Notes for PIO Beijer(V3)_Rev3006.pdf

G series, GL-9972 PIO - Update firmware

Online change with Update boot application will delay scantime

​See attached PDF file.

• WARNING! PIO will delay online change procedure (Rev 1.1).pdf

CNT-8412 (5-pin) powerplug / connector to GL-9xxx network adapters and PIO

Accessory name: CNT-8412
Part.No. 100-8186 ​

Common for both FnIO GL- and ML-series.

For example the spare part CNT-8412 power connector to be used for example to the GL-997x PIOs e.g. GL-9971/9972/9973/9974/9975 or the GL-90xx light network adapters e.g GL-9086 / 9086 / 9087 / 9089 etc. 

CODESYS Trace feature for PIO modules

The 'Trace' function is only supported in the PIO modells that inlcude the visualization. 

That include PIO models: GN-9xx3 (for example GN-9373) and GL-9973/75, GL-9981-C-x, M9xx3 and ML9973/75 series. 

Ethernet port specification of G- / M-series PIO and Network adapters

• Ethernet port specification of the G- and M-series.pdf

BCS Tools - SFC errors at compile

​Affected versions:
3.50, 3.51, 3.52
Will be solved in 3.60

Affected devices:
All devices in BCS Tools with <SP17 runtime.
BoX2 SC all variants
X2 control all variants
GL-99xx all variants
GN-93xx all variants

The reason for this is due to compatible issue between the runtime version implemented in the device and the version of the SFC library.

Workaround
Change the version in use to an older version according to the attached pictures.

• Screenshots_SFC.pdf

Not possible to add features to the CODESYS license of standard PIO

​For the standard Programmable IO of type GN-937x, GL-997x or M937x, like the GL-9972, it's NOT possible to add any additional features like protocols etc. This is because these standard PIO modules uses a fixed license setup. 

Only the Embedded Programmable I/O of GL-998x type, like the model GL-9981-C-1 that support CODESYS Application-Based Licenses, can change and add features.

Programmable IO - Release Notes / Revision history

​See attached documents showing revision history of V1.xxx - V2.xxx, and V3.xxx.

The CODESYS RT versions for each firmware revision are the following:

• PIO FW 3.xxx - CODESYS V3.5 SP17 Patch 3
  
• PIO FW 2.xxx - CODESYS V3.5 SP11 Patch 3
• PIO FW 1.xxx - CODESYS V3.5 SP11 Patch 3

• Release Notes for PIO Beijer(V1-V2)_Rev2007.pdf
• Release Notes for PIO Beijer(V3)_Rev3006 (2024-03-29).pdf

Change of retain area size Programmable IO

FnIO M-, G- and S-series Serial number and Production date

​The serieal number of S-series is 11 digits, G- and M-series is based on 12 digits.
Note, for G- and M-series the last four digits xxxx.

Shock resistance of G- and M-series (IEC 60068-2-27)

According to IEC 60068-2-27 (shock operating) standard the general shock resistance is 15G for all G- and M-series modules.

How to download Free software packages from SmartStore

​This document provides guidelines for customers when downloading free software and firmware packages from SmartStore. These procedures are described:

• How to download Free software packages from SmartStore - EXTERNAL_2023.08.08.pdf

Program example BCS Tools and iX: Modbus TCP communication between Nexto/X2control/PIO PLC and BFI-P2 BFI-H3

​This program examples can be Auto configurated in BCS Tools 3.62.

They are also available as Smart Engineering, SER0014. Either download the manual below or the complete Smart Enginnering here.

PLC-program example is intended for a Nexto, X2-control/Marine/Extreme or PIO PLC communicating by Modbus TCP with 2 pieces of BFI-P2 and BFI-H3. Version of Library file for BFIP2H3ModbusTCP functionblock is 1.0.0.2.

There is also an iX-project supporting all Beijer PLC:s, all communication buses and and all BFI.

Program example support:

• Works only towards BFI Frequency inverters
• Activate/Deactivate communication
  
• Start and stop
• Change Setfrequency
• Normal-, fast- or coasting-stop
• Inverter Alarm Reset
• Constant overview of Drive Outputs-, Alarm-, Safety-, Running Hours status
• Read and Write of all parameters and data available in the inverter
• Read of Drive type, Input voltage, Power, Frame size, Firmware and serialnumber 

One PLC-program example is intended for Nexto Xpress XP300 and any X2 HMI.

One PLC-program example is intended for X2 control and it's built-in X2 HMI.

One PLC-program example is intended for PIO, GN-9373, and any X2 HMI.

One iX-project made for any X2 to monitor/control BFI. 

Another PLC-program example is for Nexto Xpress XP340 with Webvisu.

Used softwares are BCS Tools 3.62 and iX Developer 2.50.

• SER0014_QS_BFIP2H3_ModbusTCP_V1.0.3-EN.pdf

Program example iX Developer: Project for PLC-program generated in BCS Tools or Smart Engineering for PLC communicating with BFI by bus.

​The iX project can be used for Beijer PLC communicating with BFI. It supports PLC-programs generated in BCS Tools 3.62 or Smart enginnering objects SER 0014, 0015, 0017, 0020, 0039, 0040 and 0077. Project created in iX-version 2.50.

PLC can be X2(control/Marine/Extreme), Nexto Xpress, Nexto Modular or PIO.

Buses can be one of or a mix of EtherCat, Modbus TCP, Modbus RTU, CANopen, Profinet, EtherNet IP.

Frequency inverters can be BFI-E3, BFI-P2 or BFI-H3.

• iX_BFIAllbusesV105.zip

Program example BCS Tools and iX: Modbus RTU communication between Nexto/X2control/PIO PLC and BFI-P2 BFI-H3 BFI-E3

• SER0015_QS_BFI_ModbusRTU_V2.0.0-EN.pdf

Program example BCS Tools and iX: Modbus TCP communication between Nexto/X2control/PIO PLC and BFI-E3

This program example can be Auto configurated in BCS Tools 3.62.

They are also available as Smart Engineering, SER0020.  Either download the manual below or the complete Smart Enginnering here.

Program examples are intended for a Nexto PLC NX-30xxx or XP3xx, X2-control/Marine/Extreme or PIO communicating by Modbus TCP with 2 pieces of BFI-E3 Version of Library file for BFICanOpen functionblock is 1.0.0.1.

Program example support:

• Works only towards BFI Frequency inverters BFI-E3-xxx-MTP
  
• Activate/Deactivate communication
• Start and stop
• Change Setfrequency
• Normal-, fast- or coasting-stop
• Inverter Alarm Reset
• Constant overview of Drive Outputs-, Alarm-, Safety-, Running Hours status
• Read and Write of all parameters and data available in the inverter
• Read of Drive type, Input voltage, Power, Frame size, Firmware and serialnumber 

One PLC-program example is intended for Nexto Xpress XP300 and any X2 HMI.

One PLC-program example is intended for X2 control and it's built-in X2 HMI.

One PLC-program example is intended for PIO, GN-9373, and any X2 HMI.

One iX-project made for any X2 to monitor/control BFI. 

One PLC-program example is intended for Nexto Xpress XP340 with Webvisu.

Used softwares are BCS Tools 3.62 and iX Developer 2.50

• SER0020_QS_BFIE3_ModbusTCP_V1.0.2-EN.pdf

Manual: Solution Modbus RTU communication Nexto PLC/X2control/PIO with BFI-P2 BFI-H3 BFI-E3

• SER0015_QS_BFI_ModbusRTU_V2.0.0-EN.pdf

Manual: Solution Modbus TCP communication Nexto/X2control/PIO PLC with BFI-E3

• SER0020_QS_BFIE3_ModbusTCP_V1.0.2-EN.pdf

Manual: Solution Modbus TCP communication Nexto/X2control/PIO PLC with BFI-P2 BFI-H3

• SER0014_QS_BFIP2H3_ModbusTCP_V1.0.3-EN.pdf

Remote IO serial Modbus RS485 wiring (RTU)

​How to wire Remote IO RS485 Modbus communication!

Examples with serial communication, pin configuration and wiring between:

• X2 series HMI and X2 pro/extreme/marine (SC) PLC
  to Beijer Remote IO like GL-9073 and GN-9273.
  
• GL-9972 / GL-9973 / GN-9372 / GN-9373 / M9372 / M9373 Programmable IO PLC to GN-9273 / M9273 / GL-9073 Remote IO. 
  
• Nexto Xpress PLC to GL-9073, GN-9273 and M9273 Remote IO.
• Nexto BCS-NX3003 PLC to GL-9073 Remote IO.
• Nexto BCS-NX3004/3005 PLC to GL-9073 Remote IO.
  
• Nexto BCS-NX3008, serial connected to GL-9073 Remote IO.
  
• Nexto BCS-NX3010 / 3020 / 3030 PLC to GL-9073 Remote IO.
  
  

• Remote IO serial communication wiring (Rev 1.01) 20230404.pdf

G- and GL-series Drawing, 3D / 2D CAD files (Mechanical)

​File extension: *.pdf *.dwg *.stp (step)

• FnIO-G drawings (DWG, PDF) 20221129.zip
• GL-series_3D,2D CAD File_20230103.zip
• G-series Drawing Pdf Dwg Stp 20190221.zip
• G-series_3D,2D CAD File_20230103.zip

G- and GL-series Drawing, 2D CAD files #1 (Electrical)

​File extension: *.pdf *.dwg

• G-series_2D Diagram_rev.1_20220504.zip

Conversion guide for alternative products between S-series remote IO to G- or M-series

​Use this PDF to chose a corresponding product. In some cases there are several alternatives that may need deeper investigating but in general:
- S- and G- (or M-) series modules cannot be mixed since they are mechanically different, however it is perfectly possible to have connect a S-series and G-series network adapter to the same network.
- The G-series is great all-purpose family that will work in most cases although not marine applications.
- The M-series is adapted for demanding applications and environments. It offers hot-swap and redundancy and is has a marine certifications.  

• FnIO Alternative module lists.pdf
• FnIO Alternative module lists.xlsx

G series brochure, BREN636 (english)

• 2015-429-G-series_low 2019-01-23.pdf

UL & cUL Certificate of compliance - Beijer G-series

​FnIO G-Series Network Adapters and I/O Modules 

​NRAQ.E496087 - Programmable Controllers
NRAQ7.E496087 - Programmable Controllers Certified for Canada

• E235505-vol1-MLCertificateofCompliance-E496087.pdf
• E235505-vol1-MLCorrelation-E496087.pdf

CE DoC (Declaration of Conformity) for Beijer G-series modules following the EMC & LV directive.

CE declarations for the Beijer G-series remote I/O products. 

The latest update (Rev.1.1) and attachment include modules for both EMC - Electro Magnetic Compatibility directive and the LVD - Low Voltage Directive.

• 20240808 Beijer Electronics G-series products following the EMC and LV directive (Rev.1.1).pdf
• CE DoC manuafacture declaration Beijer G-series products (Rev.1.1) 20240808 - Signed.pdf